SKU: A6316. Does your jobsite feature a flat roof surrounded by a parapet wall? If it does, then you need a way to anchor your self-retracting lifelines (SRLs). At Malta Dynamics, our parapet clamp system allows you to put your SRL in place with a sturdy connection that helps support weight and keep your workers safe. The reusable device is easy to install and won't cause damage to the wall. Your workers can use our parapet anchor on walls varying in thickness from 2.36" to 14.1".
On a jobsite, time is critical, but you never want to compromise your workers' safety. Equipment that offers intuitive usage is the best type to have on your site, as it cuts back on time without putting your employees in danger. It takes just a minute or two to secure the parapet clamp, and your workers can adjust it to reposition around the worksite.
You can feel confident in the sturdiness of our design. Our temporary parapet edge protection provides a practical solution in areas where you otherwise couldn't use an SRL.
Put Safety First When You Use Our Parapet Grabber
The anchor comes with specific directions for installation and application. Ensure your workers read and understand the instructions, as their safety depends on using the parapet clamp correctly. For example, you need a minimum wall height of 9' to use our parapet anchor.
Instructions for Installation of Parapet Clamp Fall Protection
The Parapet Anchor is intended to be installed on a parapet wall up to 14.1 inches (360mm) thick.
Unscrew the set screws so the points do not protrude into the anchor slot.
Remove the detent pin and move the adjustable arm back far enough to allow the clamp to fit over the parapet wall.
Make sure the top surface within the anchor slot is fully seated on the parapet wall.
Slide the adjustable arm toward the parapet wall and reinsert the locking pin through the position setting holes.
Tighten each set screw until it makes contact with the parapet wall. Hand tighten the screws until snug. Excessive torque can damage the parapet wall or the parapet wall anchor.
Remain in Compliance With Products From Malta Dynamics
Malta Dynamics has extensive experience manufacturing the products you need to protect your workers on the jobsite. We design our equipment with you in mind. Everything we make is easy and intuitive to use. We also consider the comfort of your employees throughout our engineering and manufacturing process.
All of our equipment is OSHA compliant, and we study federal and local guidelines to ensure you meet the necessary requirements. If you need equipment to anchor your SRLs, you can order our parapet anchor today. For more information, call us at 800-494-1840 or fill out our online contact form.
Product Downloads:
Anchor Manual
Anchor Spec Sheet
Declaration of Conformity
[ryviu_question_and_answer]
[ryviu_widget_total]
[ryviu_widget]
$378.99Original price was: $378.99.$199.99Current price is: $199.99.Add to cart
SKU: B2000-C5104. Universal Fall Protection Kit Featuring the Warthog® Pass-Thru Full-Body Harness
Equip your team with the protection they need to work confidently and safely at heights. The Malta Dynamics Fall Protection Kit is designed to provide reliable and compliant safety solutions for construction, roofing, and industrial applications.
This kit includes:
Warthog® Pass-Thru Full-Body Harness
The Warthog® Pass-Thru Harness is designed for fall arrest and fall restraint applications. Its pass-thru leg buckles provide secure and comfortable fastening, while dual lanyard keepers keep lanyards organized and out of the way. The harness is adjustable to fit workers of various sizes and includes a customizable label for recording information without compromising webbing integrity. Fully compliant with ANSI Z359 standards and OSHA requirements, this harness ensures both safety and comfort on the job.
Malta Dynamics C5104 4.5- 6’ Single Leg Internal Shock Absorbing Strech Lanyard
The Malta Dynamics 4.5′ – 6’ Single Leg Stretch Internal Shock Absorbing Lanyard with Snap Hooks is designed for use in fall arrest and restraint scenarios that require the worker to be tied-off. The internal shock absorption design keeps the webbing taut at 4.5’ when at rest and can extended out to 6’ when the extra length is needed. This lanyard is made with vibrant high-visibility orange polyester webbing, and the system can support a worker up to 310 lbs.
This fall protection kit is a dependable, cost-effective solution that helps your team work safely and confidently at heights while meeting ANSI and OSHA compliance requirements.
SKU: VARIOUS. When working on jobsites, you encounter a variety of safety hazards from every angle, that’s why proper head protection is essential. The Malta Dynamics Type 1 Safety Helmets meet the ANSI standard Z89.1-2014 for Type 1 Class C Helmets. This means they’re rated for impact to the top of your head. These helmets go one step further and are also tested to meet the EN397-2012 standard.
These safety helmets come in a variety of colors and boast a comfort-conscious design that features a 6-point suspension system, and a ratchet system allows you to tighten or loosen the fit to your preference. You can also order a safety helmet with a clear or tinted visor for added protection, and it will stay clear of fog even with long-term daily use. Every type 1 helmet has an adjustable chin strap to keep it securely in place if impact occurs. The chin strap also features a special added loop so you can easily attach it to your harness.
The Malta Dynamics line of safety helmets fit nice and low on your head instead of hoisted up on the top of the crown. They are designed to be the most comfortable helmet on the market and are equipped with strong lamp carrying clips, that are compatible with all elastic banded headlamps on the market. These helmets are also compatible with most available ear protection attachments.
Type 1 helmets from Malta Dynamics offer the flexibility and comfort your workers desire, along with the durability you need for peace of mind.
Buy a Safety Helmet With a Visor
Adding a visor to a safety helmet can make it easier for your employees to do their jobs. Standard safety glasses often need to be repositioned, but a visor keeps the lens completely off your face, freeing up your hands and eliminating pressure behind your ears.
A clear or tinted visor is the perfect accessory for your Malta Dynamics Safety Helmet. Our visors are made from high-strength plastic and meet the ANSI/ISEA Z87.1-2015 impact rating standard. The tinted visors are 99% ultraviolet (UV)-resistant to shield your eyes from the sun’s powerful rays.
What’s more, these visors are easy to use and maintain. They have a hinge feature that allows you to adjust the visor, so it’s there when you need it and stowed away when you don’t. They also have an anti-scratch lens with a rimless design that’s easy to clean — just use warm water and soap.
Our Safety Helmets Are Field-Tested and Worker-Approved
When you buy Malta Dynamics Safety Helmets, you can rest assured your workers will be safe, comfortable and compliant while wearing them. Our crew uses all of our safety equipment in the field and provides feedback to help us make our products as user-friendly and efficient as possible. We also back our safety equipment with a 100% satisfaction guarantee, so you can feel confident in your purchase.
Want to learn more about our safety helmets? You can get in touch by calling (866) 918-4319 or contacting us online.
Product Downloads:
Helmet Manual
Helmet Spec Sheet
Helmet Declaration of Conformity
Clear Visor Declaration of Conformity
[ryviu_question_and_answer]
[ryviu_widget_total]
[ryviu_widget]
$13.99–$18.99Price range: $13.99 through $18.99Select options
This product has multiple variants. The options may be chosen on the product page
SKU: NG0001. The Malta Dynamics Neck Gaiters are made of a lightweight knit fabric that is 100% polyester to keep you cool while you are protected! It also features two reflective stripes for peak visibility.
Product Downloads:
Neck Gaiter Spec Sheet
[ryviu_question_and_answer]
[ryviu_widget_total]
[ryviu_widget]
SKU: C5000. Malta Dynamics 6’ Single Leg External Shock Absorbing Lanyard with 2 Steel Snap Hooks meets all the stringent ANSI Z359.13-2009 regulations and is 100% ISO 17025 third party tested (per the ANSI testing protocols). The integrated external shock absorbing pack component limits the average arresting force to 900 pounds or less. It is comprised of 1 inch polyester webbing and two (2) 3600 ANSI tested steel snap hooks. The 6’ Single Leg External Shock Absorbing Lanyard with 2 Steel Snap Hooks is designed to be the “best in class” - functional, durable and affordable.
Product Downloads:
Lanyard Manual
Lanyard Spec Sheet
Declaration of Conformity
Lanyard Inspection Form
[ryviu_question_and_answer]
[ryviu_widget_total]
[ryviu_widget]
SKU: C7102-G2. Working at heights is a dangerous job to begin with and adding any extra weight to your load can be cumbersome and cause wasted energy. That’s why the Malta Dynamics the Pygmy Hog 6′ Self-Retracting Lifeline is designed to be the best mini retractable available on the market. Weighing in at just 2.4 lbs., the extremely lightweight Pygmy Hog is portable and can be used as one unit or in a kit of two.
The Pygmy Hog Self-Retracting Lifeline is a Webbed SRL that is manufactured from non-corrosive, lightweight components including a durable ultrahigh-molecular-weight Polyethylene (UHMWPE) & Polyester lifeline, and a durable housing made from a high strength thermoplastic polymer.
The Pygmy Hog Self-Retracting Lifeline comes equipped with a handy 360° swivel top connector that allows the unit to turn freely as you move, which keeps the lifeline from snagging or getting tangled.
This compact and lightweight Pygmy Hog SRL features a high-visibility yellow webbed cable that features a black color along the edges. The use of the black and yellow contrast makes it easier to notice cuts and frays along the lifeline during inspections. This OSHA and ANSI compliant, high-quality self-retracting lifeline is a must-have for your jobsite.
How to Inspect Your Self-Retracting Lifeline Correctly
Inspecting your equipment is an essential pre-use action, there’s no point in wearing fall protection if it’s going to fail when you need it. Using old or non-compliant safety materials can have a detrimental outcome if a fall occurs. Taking a few to inspect your gear properly has the power to save your life.
Here are some tips on how to successfully check over your self-retracting lifeline.
Examine Metal Components:
The Fall Indicator: located at the connection point on your SRL. When the force indicator has been tripped, it indicates that fall-like impact forces have been applied on the self-retracting lifeline. If the fall indicator has been tripped, you will see a red indicator at the connection point and the device should be immediately removed from service.
The Snap Hook: Ensure the mechanism opens and closes properly. Press on the gate to confirm it cannot be forced open. Please check to validate that the snap hook is not bent or deformed in any way.
Inspect the Housing:
Ensure all fasteners are present and tight.
Inspect the label for serial number, batch number, manufacture date and part number.
Inspect the Cable:
If the cable gets tangled in the housing, it is no longer adequate for arresting a fall.
Inspect the entire length of the cable for cuts, burns, frays, kinks, or tears.
Perform a Strike Test:
Grip the handle and quickly pull downward on the cable, place all the force above the fall indicator so you do not accidentally trigger it.
This will test the braking mechanism of your SRL
If you follow these tips and perform regular inspections, you will keep your SRL healthy for years of use. We also have handy downloadable safety inspection forms to help guide you through your SRL examination.
Malta Dynamics – Field Tested, Worker Approved
At Malta Dynamics, we have the unique advantage of having a crew who uses our safety equipment in the field and actively sends feedback to help us make our products as efficient and user-friendly as possible. We engineer, manufacture, and personally use all of our safety fall protection solutions. We are proud to offer a 100% satisfaction guarantee, we want you to have confidence that your workers will be safe, comfortable, and compliant while using our creations.
No matter what industry you work in, we have gear that has been proven to withstand harsh environments and outperform trade safety standards. With over thirty years of experience in the construction industry, we have become experts in safety so you can count on us to cater all your safety needs.
Have any general questions about our products? Interested in learning more about our Malta Dynamics Hybrid Hog SRL? Our team will assist you in finding the right safety solutions. Call 800-494-1840 for a representative or fill out our form.
Product Downloads:
SRL Manual
SRL Spec Sheet
Declaration of Conformity
SRL Inspection Form
[ryviu_question_and_answer]
[ryviu_widget_total]
[ryviu_widget]
SKU: C7012. The 50’ Roofer’s Safety Bucket Kit is the ultimate choice for roofing applications, offering a complete personal fall arrest system in a reusable 5-gallon bucket. This all-in-one roofer's kit includes a lightweight, universal-sized fall protection harness with pass-thru chest and leg straps, a 50′ vertical lifeline assembly with a shock absorber rope grab, and a heavy-duty, zinc-plated reusable roof anchor. Designed to simplify safety decisions, the kit meets stringent ANSI and OSHA standards, ensuring compliance and reliability. With exceptional quality at an affordable price, Malta Dynamics makes fall protection equipment safe, easy, and accessible for all roofing professionals.
Roof Safety Harness Kit Includes:
Harness
Anchor
Vertical Lifeline Assembly
Need other equipment for your fall protection kit? Check out our full selection including: shock absorbing lanyards, fall arrest harnesses, and more!
[ryviu_question_and_answer]
[ryviu_widget_total]
[ryviu_widget]
SKU: HEA1002. Crafted from heavy-duty steel and rated to support up to 5,000 lbs., the Dual-Action Twist Lock Carabiner delivers dependable strength for every whitetail hunt. Whether you're getting settled into your tree stand or clipping into your Tree Strap or Lifeline, these carabiners are built to perform quietly and reliably.
The intuitive one-hand operation helps reduce movement and noise, while the self-closing, auto-locking gate keeps you secure during climbs, transitions, and long sits. Finished with a corrosion-resistant coating, they hold up through humid early-season hunts, cold November mornings, and everything in between.
*Not intended for Construction Use
SKU: VARIOUS. The Malta Dynamics Insulated Cut Level A4 Work Gloves are designed to protect hands in cold-weather environments while maintaining comfort and dexterity. Featuring cut-resistant materials and a polyurethane palm coating, these gloves provide excellent grip and long-lasting durability. The insulated lining keeps hands warm, and the touchscreen-compatible design allows workers to use devices without removing their gloves. Sold in a 12-pack, these gloves are a practical choice to keep crews safe and productive on the job.
Product Downloads:
Gloves Spec Sheet
Gloves Declaration of Conformity
[ryviu_question_and_answer]
[ryviu_widget_total]
[ryviu_widget]
$71.99Select options
This product has multiple variants. The options may be chosen on the product page
SKU: C5117. Malta Dynamics 4.5' - 6’ Double Leg Stretch Internal Shock Absorbing Lanyard with 2 Rebar Hooks and 1 Steel Snap Hook is specifically designed to help reduce the hazards of tripping or catching on nearby machinery found on many of today’s industrial and construction sites. This lanyard is ideal for work in tight spaces and around machinery. This lanyard is designed to stretch from 4.5 feet when at rest out to 6 feet when needed. It is available in a variety of connector options, as well as both single and double leg models. Double leg lanyards are for fall arrest and 100% tie off.
Product Downloads:
Lanyard Manual
Lanyard Spec Sheet
Declaration of Conformity
Lanyard Inspection Form
[ryviu_question_and_answer]
[ryviu_widget_total]
[ryviu_widget]
SKU: VARIOUS. The Malta Dynamics Full Brim Hard Hat is engineered to provide reliable protection and all-day comfort for workers in demanding environments. Designed for top impact protection, this hard hat meets ANSI Z89.1 Type 1 Class E and Class G standards, offering electrical insulation up to 20,000 volts (Class E) and general protection for a wide range of jobsite applications. It is also compliant with OSHA 1910 and 1926 regulations, keeping your crew fully protected and jobsite ready. Constructed from a rugged, lightweight polyethylene shell, the full brim design delivers durability without sacrificing comfort. The 4-point suspension system with front and rear vertical height adjustments ensures a secure, customized fit, while the ratchet system with cushion pillows and a nape cushion provides enhanced comfort for extended wear. Available in White, Grey, Black, Yellow, Blue, Red, Orange, and Green this hard hat offers both safety and professional style. Manufactured in an ISO 9001 registered facility and made in the USA, this hard hat combines rugged performance with professional-grade safety. At Malta Dynamics, we understand that your safety gear should also reflect your brand. That’s why we offer custom logo printing, allowing you to outfit your crew with hard hats that showcase your company’s identity while delivering premium protection. Field Tested. Field Approved. Trusted by real crews working in real-world conditions.
Hard Hat Spec Sheet
Hard Hat Assembly Instructions
HHBLK2004 Declaration of Conformity
HHG2004 Declaration of Conformity
HHY2004 Declaration of Conformity
HHB2004 Declaration of Conformity
HHO2004 Declaration of Conformity
HHR2004 Declaration of Conformity
HHW2004 Declaration of Conformity
HHGN2004 Declaration of Conformity
[ryviu_question_and_answer]
[ryviu_widget_total]
[ryviu_widget]
$9.99–$27.99Price range: $9.99 through $27.99Select options
This product has multiple variants. The options may be chosen on the product page
SKU: HH400D. The Malta Dynamics line of Hard Hat Mounted Face Protection is designed specifically as an accessory to the Malta Dynamics’ Cap Style Hard Hat line. When jobsite applications demand both head and face protection our wide variety of products are compliant, safe, durable and affordable. The Malta Dynamics flat acetate visor is to be used in conjunction with the Malta Dynamics brand face shield brackets to protect against light chemical splashes and impacts. Brackets are available in several mounting styles that attach securely to Malta Dynamics’ hard hats.
Malta Dynamics’ visors conform to ANSI/ISEA Z87.1-2010 standard for face protection when used in combination with Malta Dynamics’ headgear or face shield brackets. Products available for both high heat, high impact and basic impact applications.
*Always wear ANSI Z87.1-2003 approved goggles or safety glasses with face shield frames and visors for maximum protection.
Product Downloads:
Bracket Spec Sheet
Declaration of Conformity
[ryviu_question_and_answer]
[ryviu_widget_total]
[ryviu_widget]
SKU: HEA1230-KIT. LINEMAN’S CLIMBING STRAP
The Malta Hunting Safety Lineman’s Climbing Strap is crafted to accompany our complete line of Malta Hunting Harnesses perfectly. Using the strap allows you to safely climb a tree to install your tree stands or steps while keeping your hands free. The high-strength polyester strap is easily adjustable and features steel carabiners that attach directly to the sewn-in Lineman’s Loops on our Malta Hunting Harnesses. Wrap the strap around the trunk and adjust the tension using the steel buckle as you ascend the tree.
Note: This accessory must be used in conjunction with a Tree Strap, Safety Harness, and Harness Tether.
TREE STRAP
The Malta Hunting Safety Tree Strap is crafted to accompany our complete line of Malta Hunting Harnesses perfectly. This strap is made with high-strength polyester webbing that won’t rip or tear and provides ideal friction to keep you safely attached to the tree. The strap allows you to anchor safely to the tree during your hunt. Tighten the tension buckle around the tree high enough to keep your harness tether taut when in a seated position, attach the tether to your harness, and safely hunt from all angles.
DEER DRAG/SUSPENSION RELIEF STRAP
The Malta Hunting Safety Deer Drag/Suspension Relief Strap is a double whammy when it comes to hunting safety accessories. The strap has been designed to work seamlessly with our complete line of Malta Hunting Harnesses. Arresting an accidental fall is just the first step to making sure a hunter is safely rescued. In the time it takes to retrieve the fallen hunter, numerous secondary complications and injuries can occur. While suspended, the femoral arteries, which are located on the inner thigh, are vulnerable to excess pressure. If a fall occurs, step into the loop located on the end of the Suspension Relief Strap and alternate standing on each foot to allow blood to keep circulating freely throughout the body. To use the strap as a Deer Drag, wrap the loop around the deer’s limb to create a slip knot and start your drag.
Product Downloads:
HUNTING ACCESSORIES SPEC SHEET
SKU: VARIOUS. A full-body harness is an integral part of a personal fall arrest system that helps ensure safety while working at heights. When combined with other fall protection equipment, these nylon, polyester, and steel harnesses protect vital organs and prevent casualties by stopping impact with the ground during a fall.
The Javelina Full-Body Harness with Quick Connect Chest Buckles and Tongue & Buckle Legs is the best available economy harness on the market. This roof safety harness can be used with a worker capacity range of 130 to 310 lbs. and has been tested to ANSI and OSHA fall protection standards that include ANSI Z359.11-2021, OSHA 1910.66, and OSHA 1926.502, Subpart M. No matter the project, these harnesses can withstand tough tasks day in and day out.
The Javelina fall protection harness has dual break-away lanyard keepers to hold lanyards out of the way while working and comes with a customizable label where workers can record information on harnesses without jeopardizing the integrity of the webbing.
Because Javelina safety harnesses are constructed as a one-piece structure, workers can trust that it will stay in place without slipping. This harness features tongue and buckle leg connections with metal grommets that can be easily adjusted and tightened to help achieve the perfect fit. The quick-connect check buckle allows workers to set their perfect fit and makes getting in out of the harness quick and simple. Whatever your workers’ size requirements are, the Javelina Full-Body Harness can be customized to meet their needs — without damaging the webbing.
The Javelina Full Body Back D-Ring Universal Harness with Tongue and Buckle Legs and Quick Connect Chest fasteners is the harness that everyone says they want, but no one makes. Well, Malta Dynamics listens to our customers’ requests and now offers the ideal harness for long days on the jobsite.
How to Adjust and Wear the Javelina Harness
While the Javelina full-body harness delivers reliable protection, it's important to ensure it's properly adjusted at all times. Your business's harnesses need to be regularly inspected, and each worker needs to ensure their harness fits correctly. You can do this by:
Holding the D-Ring, shake the Javelina safety harness, and then unfasten any straps.
Slipping the straps over your shoulders, making sure the D-Ring is centered on your back.
Putting each leg through the straps and then attaching the straps to the connector.
Fastening the waist belt, if your harness has one.
Connecting the chest strap, which should stay 6 to 8 inches under your throat.
Experience Industry-Leading Fall Protection and Safety Harnesses
At Malta Dynamics, we have over three decades of experience in the construction industry creating fall protection and safety harnesses that our own team uses every day. As a full-service manufacturing company, we understand which safety, performance and comfort features you desire and work to exceed all your expectations.
Our Javelina full-body Harness has been both designed and tested to keep your workers safe. Malta Dynamics is a trusted industry leader, putting safety first across an array of industries throughout the nation.
With your purchase, you can experience peace of mind with our 100% satisfaction guarantee on all harnesses. Interested in learning more? Reach out to us by calling us at 800-494-1840 or filling out our online contact form. We'll be in touch with you soon.
Product Downloads:
Harness Selection Guide
Harness Manual
Harness Spec Sheet
Declaration of Conformity
Harness Inspection Form
[ryviu_question_and_answer]
[ryviu_widget_total]
[ryviu_widget]
$97.99Original price was: $97.99.$59.99Current price is: $59.99.Select options
This product has multiple variants. The options may be chosen on the product page
SKU: C7104D-G2. The 6’ Pygmy Hog SRL with Rebar Hook from Malta Dynamics is a versatile, light-weight Personal lifeline for many applications. The bright poly webbing is easy to inspect, and the hard polymer exterior is durable for everyday use. This 6’ Class 1-P is designed for above back D-Ring use and can be used as a single lifeline with its 360-degree swivel top or can be used for 100% tie-off as a dual lifeline.
The popular Rebar hook is also known as a pelican or scaffold hook and has a wider gate opening to accommodate a variety of anchorages. The interior braking mechanism, and exterior shock pack work together to arrest a fall on workers up to 310 lbs. These features along with our ‘Field Tested, Field Approved’ stamp of approval make the 6’ Pygmy Hog SRL with Rebar Hook is one of the most dependable and usable personal lifelines.
Product Downloads:
SRL Manual
SRL Spec Sheet
SRL Declaration of Conformity
SRL Inspection Form
Connector Manual
Connector Spec Sheet
Connector Declaration of Conformity
How to Inspect Your Self Retracting Lifeline Correctly
Inspecting your equipment is an essential action when ensuring safety. There’s no point in wearing a lifeline if it’s going to fail when you need it. Using old or inadequate safety materials can have a detrimental outcome if a fall occurs. It’s important to inspect your gear prior to each and every use; your life is literally on the line, so take the time to examine your equipment.
Here are some tips on how to successfully check over your self-retracting lifeline.
Examine Metal Components
The Fall Indicator: located at the connection point on your SRL. When the force indicator has been tripped, it indicates that fall-like impact forces have been applied on the self-retracting lifeline. If the fall indicator has been tripped, you will see a red indicator at the connection point and the device should be immediately removed from service.
The Snap Hook: Ensure the mechanism opens and closes properly. Press on the gate to confirm it cannot be forced open. Please check to validate that the snap hook is not bent or deformed in any way.
Inspect the Housing:
Ensure all fasteners are present and tight.
Inspect the label for serial number, batch number, manufacture date and part number.
Inspect the Cable:
If the cable gets tangled in the housing, it is no longer adequate for arresting a fall.
Inspect the entire length of the cable for cuts, burns, frays, kinks, or tears.
Perform a Strike Test:
Grip the handle and quickly pull downward on the cable, place all the force above the fall indicator so you do not accidentally trigger it.
This will test the braking mechanism of your SRL.
If you follow these tips and perform regular inspections, you will keep your SRL healthy for years of use. We also have handy downloadable safety inspection forms to help guide you through your SRL examination.
Malta Dynamics – Field Tested, Worker Approved
At Malta Dynamics, we have the unique advantage of having a crew who uses our safety equipment in the field that actively sends feedback to help us make our products as efficient and user-friendly as possible. We engineer, manufacture, and personally use all of our safety fall protection solutions. We are proud to offer a 100% satisfaction guarantee, we want you to have confidence that your workers will be safe, comfortable, and compliant while using our safety products.
No matter what industry you work in, we have gear that has been proven to withstand harsh environments and outperform trade safety standards. With over thirty years of experience in the construction industry, we have become experts in safety so you can count on us to cater to all your safety needs.
Have any general questions about our products? Our team will assist you in finding the right safety solutions. Call 800-494-1840 for a representative or fill out our form.
[ryviu_question_and_answer]
[ryviu_widget_total]
[ryviu_widget]
SKU: VARIOUS. Malta Dynamics has put together a hard hat visor kit that is designed to give full protection for both your head and face at the same time. This kit includes one of our fan favorites, a 4 Pt. Ratchet Full Brim Style Hard Hat, and a full face visor with a bracket for attachment to the hard hat. The standard hard hat with a full brim features a poly brow pad and four points of attachment for a more secure fit. The full brim on the hat protects against splash, glare, and sun exposure, while the ratchet system allows for a snug and comfortable custom fit.
These hard hats are tested to the highest of standards and comply with ANSI Type E & G regulations. Class G testing means that sample shells must be proof-tested to 2,200 volts, offering protection to those exposed to low-voltage electrical conductors, and the helmet should decrease the impact of falling objects. A Class E rating means that sample shells proof-tested to 20,000 volts, protecting people exposed to high voltage electrical conductors. The helmet also lessens the impact of falling objects.
The Malta Dynamics flat acetate visor is to be used in conjunction with the Malta Dynamics brand face shield brackets to protect against light chemical splashes and impacts. Malta Dynamics visors conform to ANSI/ISEA Z87.1-2010 standards and meet OSHA 1910.135 and 1926.100 for face protection when used in combination with Malta Dynamics headgear or face shield brackets.
Product Downloads:
Hard Hat Spec Sheet
Hard Hat Assembly Instructions
[ryviu_question_and_answer]
[ryviu_widget_total]
[ryviu_widget]
$61.99Select options
This product has multiple variants. The options may be chosen on the product page
