-
PARAPET ANCHOR
SKU: A6316. Does your jobsite feature a flat roof surrounded by a parapet wall? If it does, then you need a way to anchor your self-retracting lifelines (SRLs). At Malta Dynamics, our parapet clamp system allows you to put your SRL in place with a sturdy connection that helps support weight and keep your workers safe. The reusable device is easy to install and won't cause damage to the wall. Your workers can use our parapet anchor on walls varying in thickness from 2.36" to 14.1". On a jobsite, time is critical, but you never want to compromise your workers' safety. Equipment that offers intuitive usage is the best type to have on your site, as it cuts back on time without putting your employees in danger. It takes just a minute or two to secure the parapet clamp, and your workers can adjust it to reposition around the worksite. You can feel confident in the sturdiness of our design. Our temporary parapet edge protection provides a practical solution in areas where you otherwise couldn't use an SRL. Put Safety First When You Use Our Parapet Grabber The anchor comes with specific directions for installation and application. Ensure your workers read and understand the instructions, as their safety depends on using the parapet clamp correctly. For example, you need a minimum wall height of 9' to use our parapet anchor. Instructions for Installation of Parapet Clamp Fall Protection The Parapet Anchor is intended to be installed on a parapet wall up to 14.1 inches (360mm) thick. Unscrew the set screws so the points do not protrude into the anchor slot. Remove the detent pin and move the adjustable arm back far enough to allow the clamp to fit over the parapet wall. Make sure the top surface within the anchor slot is fully seated on the parapet wall. Slide the adjustable arm toward the parapet wall and reinsert the locking pin through the position setting holes. Tighten each set screw until it makes contact with the parapet wall. Hand tighten the screws until snug. Excessive torque can damage the parapet wall or the parapet wall anchor. Remain in Compliance With Products From Malta Dynamics Malta Dynamics has extensive experience manufacturing the products you need to protect your workers on the jobsite. We design our equipment with you in mind. Everything we make is easy and intuitive to use. We also consider the comfort of your employees throughout our engineering and manufacturing process. All of our equipment is OSHA compliant, and we study federal and local guidelines to ensure you meet the necessary requirements. If you need equipment to anchor your SRLs, you can order our parapet anchor today. For more information, call us at 800-494-1840 or fill out our online contact form. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
3/4″ REMOVABLE CONCRETE ANCHOR 5K
SKU: A6002. The 3/4" Removable Concrete Anchor 5K (Part # A6002) is designed for use in 12-inch thick cured concrete with a compression strength of at least 3000 p.s.i. The concrete anchor is easy to install, just compress its spring and insert the cable shaft into the hole. This anchor may be used on vertical and overhead surfaces, as well as in combination with horizontal lifelines. It is suitable for fall arrest, restraint, and as a work positioning device. It has a maximum capacity of 400 pounds when used in combination with equipment certified for loads in excess of the OSHA and ANSI regulated maximum of 310 pounds. The 3/4" reusable Concrete Anchor fits holes of 3/4 inches in diameter and 3 inches deep, and has an ultimate breaking strength of 5,000 pounds. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity -
Roof Anchor 18″ Threaded Top with Swivel Anchor
SKU: A7320-A6306. The Malta Dynamics Threaded Top 18" Roof Anchor is a fixed post rooftop anchor, intended for permanent applications only. The A6306 has been thoroughly tested (see testing and compliance page on this product) and is compatible for installation on steel and concrete substrates (fasteners sold separately). The 18-inch anchor post functions to extend through roofing materials so that it is accessible both during and after roof construction. The A6306 roof safety anchor is composed of durable galvanized steel, and is compatible for use with SRLs, vertical lifelines, and shock absorbing lanyards. The Malta Dynamics 5K Swivel Anchor rotates 360 degrees, flips 180 degrees, and is zinc coated steel. Mounting hardware included. Meets ANSI Z359.18-2017 and ANSI A10.32-12 Compliant with OSHA 1910 and OSHA 1926 Subpart M Product Weight: 1.5 lbs. Simple mount and bolt on system Easy installation and removal Swivels full 360° Great for first-man-up system Worker Capacity Range: 130-310 lbs. Material: Zinc plated steel Min. Breaking Strength: 5,000 lbs. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
ROOF ANCHOR 18″ THREADED TOP Super Sale! $99.99 (while supplies last)
SKU: A6306. The Malta Dynamics Threaded Top 18" Roof Anchor is a fixed post rooftop anchor, intended for permanent applications only. The A6306 has been thoroughly tested (see testing and compliance page on this product) and is compatible for installation on steel and concrete substrates (fasteners sold separately). The 18-inch anchor post functions to extend through roofing materials so that it is accessible both during and after roof construction. The A6306 roof safety anchor is composed of durable galvanized steel, and is compatible for use with SRLs, vertical lifelines, and shock absorbing lanyards. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
ROOF ANCHOR USA EDITION 12″ or 18″
SKU: A6300/01 Family. The Malta Dynamics Roof Anchor is a fixed-post anchorage solution designed for permanent installation on steel, wood, or concrete rooftops. Available in both 12” and 18” heights, this anchor extends above the finished roof surface to provide a visible, accessible tie-off point-ideal for both new construction and ongoing maintenance work. Choose the 12” model for standard roof setups, or select the 18” option when working with deeper roof substrates that require additional clearance above flashing, insulation, or decking layers. Both versions are constructed from heavy-duty galvanized steel for long-lasting performance and corrosion resistance in tough weather conditions. The round post design fits most standard flashing kits, ensuring a clean, secure install. Each anchor is rated to a 5,000 lb. minimum breaking strength and is fully compliant with ANSI Z359.18-2017, OSHA 1926 Subpart M, and OSHA 1910 standards. Compatible with self-retracting lifelines (SRLs), vertical lifelines, and shock-absorbing lanyards, the Malta Dynamics Roof Anchor also meets window cleaning system requirements—making it a dependable solution for a wide range of elevated work applications. Proud to buy American? Prefer the quality? Maybe you're encouraged to source locally? Either way, this Malta Dynamics Roof Anchor's got your back! Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity 12" Declaration of Conformity 18" [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget]Price range: $277.99 through $317.99 Select options This product has multiple variants. The options may be chosen on the product page -
Roof Anchor 12″ Threaded Top with Swivel Anchor
SKU: A7320-A6305. The Malta Dynamics Threaded Top 12" Roof Anchor is a fixed post roof top safety anchor, intended for permanent applications only. The A6305 has been thoroughly tested (see testing and compliance page on this product) and is compatible for installation on steel and concrete substrates (fasteners sold separately). The 12-inch anchor post functions to extend through roofing materials so that it is accessible both during and after roof construction. The A6305 permanent roof anchor is composed of durable galvanized steel, and is compatible for use with SRLs, vertical lifelines, and shock absorbing lanyards. The Malta Dynamics 5K Swivel Anchor rotates 360 degrees, flips 180 degrees, and is zinc coated steel. Mounting hardware included. Meets ANSI Z359.18-2017 and ANSI A10.32-12 Compliant with OSHA 1910 and OSHA 1926 Subpart M Product Weight: 1.5 lbs. Simple mount and bolt on system Easy installation and removal Swivels full 360° Great for first-man-up system Worker Capacity Range: 130-310 lbs. Material: Zinc plated steel Min. Breaking Strength: 5,000 lbs. Anchor Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity Swivel Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
4-WAY ANCHOR PLATE
SKU: A6304. The Malta Dynamics Multi-Directional Roof Anchor supports one worker in fall arrest or two workers in fall restraint. The four directional connection points increase the working range (when detaching and reattaching to connection points). Workers can maintain both fall arrest or fall restraint. It is designed and tested to meet the latest ANSI Z359.18-2017 standard, ensuring optimal safety and performance for workers. This anchor supports one worker in fall arrest and two workers in fall restraint, featuring four directional connection points that enhance mobility and ease of use. Its versatile design allows workers to safely detach and reattach to connection points while maintaining fall protection, making it an ideal solution for various roofing applications. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
4’ MALTA DYNAMICS CONCRETE ANCHOR STRAP
SKU: A6400. The Malta Dynamics Concrete Anchor Strap is made up of a strong polyester web inner core which is further protected by a heavy-duty polyester web sheath. The premium sheath protects the inner core from abrasion and wear and extends its overall life. The Malta Dynamics Concrete Anchor strap can be used as a permanent anchor during building construction or as a temporary anchor in applications such as wood framework, rebar work, or pipe racking. As always, be sure the selected attachment point can withstand anticipated fall loads and meet or exceed OSHA required anchorage strength requirements. When attached to a suitable structure, the Malta Dynamics Concrete Anchor Strap provides workers with a safe, compliant anchor point. Instructions for Installation: Select a safe location for the Concrete Anchor Strap. The location must meet the OSHA-required minimum anchor strength requirement. In cases of doubt please contact a qualified or competent person for more information. Once a section of wall of concrete column has been poured and cured, place Concrete Anchor Strap User Instruction Manual MaltaDynamics.com | 800-494-1840 12 Manual Revision Code: MD-CASUIM 11-12-18 the looped end of the anchor onto a vertical piece of steel rebar. After the anchor(s) are in place, continue to pour concrete, allowing it to cure fully. After removing forms, anchors will remain on the face of the column or in between the seams of shear walls. For Reinforced Concrete Floor Slabs: A three-foot length of rebar may pass through the loop end of the anchor strap and wire tied to remain tightly in place to the underside of the upper mat of rebar. This provides 3.5” of clearance. Concrete can then be poured, and the anchor strap will become cast into place for use after curing is finished. Free fall distance must not exceed six feet at any time. Locate the attachment point to the anchor at or above the connection point of the fall arrest equipment to the harness. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
4’ MALTA DYNAMICS WEB ONLY CONCRETE ANCHOR STRAP
SKU: A6401. The Malta Dynamics Concrete Anchor Strap is made up of a strong polyester web inner core which is further protected by a heavy duty polyester web sheath. The premium sheath protects the inner core from abrasion and wear and extends its overall life. The Malta Dynamics Concrete Anchor strap can be used as a permanent anchor during building construction or as a temporary anchor in applications such as wood framework, rebar work, or pipe racking. As always, be sure selected attachment point can withstand anticipated fall loads and meet or exceed OSHA required anchorage strength requirements. When attached to a suitable structure, the Malta Dynamics Concrete Anchor Strap provides a safe, compliant anchor point for workers. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
5K SWIVEL ANCHOR
SKU: VARIOUS. The Malta Dynamics 5K Swivel Anchor is a reliable safety anchor designed for workers at heights, suitable for use in both steel and concrete applications. This anchor is built tough to ensure workers' safety, meeting or exceeding industry standards for fall protection. It can be easily integrated into steel structures and concrete applications, providing a secure attachment point. With a 5,000-pound minimum breaking strength, this swivel anchor is strong and durable, offering workers the stability they need when working at heights. Its 360 degree swivel design with the ability to flip 180 degrees allows for easy movement, reducing the risk of entanglement and ensuring freedom of motion. Product Downloads: Anchor Manual Anchor Spec Sheet A7360 Declaration of Conformity A7360C Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget]Price range: $74.99 through $79.99 Select options This product has multiple variants. The options may be chosen on the product page -
ROOF ANCHOR 12″ THREADED TOP Super Sale! $99.99 (while supplies last)
SKU: A6305. The Malta Dynamics Threaded Top 12" Roof Anchor is a fixed post roof top safety anchor, intended for permanent applications only. The A6305 has been thoroughly tested (see testing and compliance page on this product) and is compatible for installation on steel and concrete substrates (fasteners sold separately). The 12-inch anchor post functions to extend through roofing materials so that it is accessible both during and after roof construction. The A6305 permanent roof anchor is composed of durable galvanized steel, and is compatible for use with SRLs, vertical lifelines, and shock absorbing lanyards. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget]
CONCRETE ANCHORS
How Do Concrete Anchors Work?
Concrete anchors are designed to support the weight of a worker in the event of a fall. They attach securely to concrete surfaces, preventing the worker from hitting the ground. Our concrete anchors are available in various types, including stainless steel anchors and carbon steel options, all engineered for heavy-duty use.
Concrete anchors can be installed either by embedding them while the concrete is being poured or by drilling into hardened concrete. This allows flexibility depending on your project’s stage. Using a hammer drill, you can create the right hole size and depth for installation. Some types, like epoxy anchors and wedge anchors, expand upon insertion, ensuring a secure fit.
CALL NOWWhy You Need Concrete Anchors From Malta Dynamics
Concrete anchors are essential components of personal fall arrest systems (PFAS), specifically designed for securing workers while working at heights. At Malta Dynamics, our high-quality concrete anchors are built to provide reliable support on various surfaces like concrete slabs, brick walls, and more. Whether you’re working on heavy-duty applications or light-duty tasks, we offer a range of anchors to suit your job’s demands, ensuring proper installation and compliance with OSHA regulations. With our products, you can ensure worker safety and mitigate the risk of fall hazards.
Concrete anchors from Malta Dynamics, including wedge anchors, sleeve anchors, and drop-in anchors, can be used in solid concrete, pre-drilled holes, or even concrete slabs. These heavy-duty fasteners are ideal for high-performance applications, providing the highest level of security on the job site.
Types of Concrete Anchors
Wedge Anchors
Concrete wedge anchors are known for their heavy-duty capabilities and are ideal for securing threads into solid concrete. These anchors expand after installation, providing strong, reliable support.
Sleeve Anchors
Ideal for both brick walls and concrete, sleeve anchors offer versatility across different base materials. They’re great for fastening heavy-duty applications and can support significant weight, especially in high-performance environments.
Drop-In Anchors
These anchors are inserted into a pre-drilled hole using a hammer drill. Upon insertion, they expand and lock into place, offering robust support for threaded rods or leadwood screw anchors.
Removable Concrete Anchors
Our removable anchors, such as wedge anchors, are easy to install and remove, providing flexibility for jobs that require temporary installations in concrete slabs or other base materials.
Choosing the Right Concrete Anchor
Choosing the Right Anchor
When selecting the right concrete anchor, consider factors like the diameter, length, and intended application. For heavy-duty applications, anchors like wedge anchors and sleeve anchors made from stainless steel or carbon steel are perfect for providing extra security. For lighter applications, you may opt for light-duty anchors that are easier to install with a basic hand tool or screw.
Installation Tips for Concrete Anchors
To ensure your concrete anchors are installed correctly, always use the proper carbide drill bit and hammer drill to achieve the appropriate hole size and depth. For wedge anchors and epoxy anchors, follow the specific instructions regarding cure time and expansion to avoid any failure in performance. For threaded rods and nuts, ensure that the threads are aligned correctly to prevent wear and tear.
Meeting ANSI and OSHA Standards
All Malta Dynamics concrete anchors meet or exceed ANSI and OSHA standards, ensuring that your job site remains safe and compliant. By using our anchors, you are not only protecting your workers but also safeguarding your organization against potential regulatory violations.
Discover the Malta Dynamics Difference
At Malta Dynamics, we understand the importance of high-quality safety products. Our concrete anchors are crafted with durability in mind, suitable for various job site conditions, whether you’re working with wood, concrete, or other base materials. Trust us to provide the best solutions for your needs, whether you’re dealing with concrete patch-ties, lag bolts, or red head anchors.
Choose Malta Dynamics for Concrete Anchors
Meeting ANSI and OSHA Standards
Explore our full range of fall protection products today, including bolts, drill bits, and anchors, and discover why Malta Dynamics is the trusted name in safety equipment.
Need assistance with selecting the right concrete anchor? Contact us today to learn more about our products or to request a consultation.
Frequently Asked Questions
What is a concrete wedge anchor, and when should it be used?
A concrete wedge anchor is a heavy-duty fastener designed to secure materials to solid concrete. It is commonly used in heavy-duty applications like anchoring steel columns, beams, and support brackets. Proper installation requires drilling a pre-drilled hole into the concrete using a carbide drill bit and tightening the nut to secure the anchor. These are ideal for high-performance needs in construction projects where strength and reliability are critical.
How do you install sleeve anchors in concrete?
To install sleeve anchors in concrete, start by drilling the appropriate hole size with a hammer drill. Insert the sleeve anchor into the hole, ensuring the bolt head is flush with the surface. Tighten the nut, which causes the sleeve to expand, securing the anchor in place. Sleeve anchors are commonly used in light-duty applications, like securing door frames or window installations to concrete walls.
What is the difference between a drop-in anchor and a wedge anchor?
A drop-in anchor is internally threaded and used for securing bolts or threaded rods to solid concrete, making it ideal for overhead applications. In contrast, a wedge anchor expands as the bolt is tightened, providing a strong and heavy-duty hold. Drop-in anchors require a pre-drilled hole and are often used in high-performance projects, while wedge anchors are preferred for fast installation in structural work.
How do you choose the right fastener for masonry and concrete?
Choosing the right fastener depends on the base material and application. For brick walls or concrete slabs, consider using epoxy anchors or masonry anchors like leadwood screw anchors. For heavy-duty applications, concrete wedge anchors or stainless steel anchors are often recommended. Ensure the fastener matches the load capacity and project requirements to ensure safety and stability.
What tools are needed for proper installation of concrete anchors?
For the proper installation of concrete anchors, you’ll need a hammer drill with a carbide drill bit to create the correct hole size. Depending on the anchor type, you may also need a hand tool or wrench to tighten screws or nuts. Using high-quality tools is essential to ensure the anchor’s stability in heavy-duty construction applications, especially for securing elements to solid concrete or brick walls.
