From window washing to restoration, investing in high-quality safety anchors ensures your employees remain safe if a fall were to occur. At Malta Dynamics, we have residential and commercial anchor solutions so that you and your employees can enjoy greater peace of mind.
-
PARAPET ANCHOR
SKU: A6316. Does your jobsite feature a flat roof surrounded by a parapet wall? If it does, then you need a way to anchor your self-retracting lifelines (SRLs). At Malta Dynamics, our parapet clamp system allows you to put your SRL in place with a sturdy connection that helps support weight and keep your workers safe. The reusable device is easy to install and won't cause damage to the wall. Your workers can use our parapet anchor on walls varying in thickness from 2.36" to 14.1". On a jobsite, time is critical, but you never want to compromise your workers' safety. Equipment that offers intuitive usage is the best type to have on your site, as it cuts back on time without putting your employees in danger. It takes just a minute or two to secure the parapet clamp, and your workers can adjust it to reposition around the worksite. You can feel confident in the sturdiness of our design. Our temporary parapet edge protection provides a practical solution in areas where you otherwise couldn't use an SRL. Put Safety First When You Use Our Parapet Grabber The anchor comes with specific directions for installation and application. Ensure your workers read and understand the instructions, as their safety depends on using the parapet clamp correctly. For example, you need a minimum wall height of 9' to use our parapet anchor. Instructions for Installation of Parapet Clamp Fall Protection The Parapet Anchor is intended to be installed on a parapet wall up to 14.1 inches (360mm) thick. Unscrew the set screws so the points do not protrude into the anchor slot. Remove the detent pin and move the adjustable arm back far enough to allow the clamp to fit over the parapet wall. Make sure the top surface within the anchor slot is fully seated on the parapet wall. Slide the adjustable arm toward the parapet wall and reinsert the locking pin through the position setting holes. Tighten each set screw until it makes contact with the parapet wall. Hand tighten the screws until snug. Excessive torque can damage the parapet wall or the parapet wall anchor. Remain in Compliance With Products From Malta Dynamics Malta Dynamics has extensive experience manufacturing the products you need to protect your workers on the jobsite. We design our equipment with you in mind. Everything we make is easy and intuitive to use. We also consider the comfort of your employees throughout our engineering and manufacturing process. All of our equipment is OSHA compliant, and we study federal and local guidelines to ensure you meet the necessary requirements. If you need equipment to anchor your SRLs, you can order our parapet anchor today. For more information, call us at 800-494-1840 or fill out our online contact form. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
BEAM TROLLEY 3″ – 10″ 5K
SKU: A6101. The Malta Dynamics Beam Trolley represents a significant leap in fall protection and mobility for individuals working at heights. Engineered for maximum safety and efficiency, this beam trolley is the ultimate solution for those requiring a reliable beam anchor device. With its innovative design and robust construction, it provides a seamless blend of functionality and durability, ensuring workers stay safely tied off while maximizing their range of movement. How to Install the Beam Trolley Installation is straightforward with this Malta Dynamics safety I-Beam rolling anchor. You can spend less time installing and more time getting to work. Before installing the safety anchor, carefully inspect it, along with the beam you will be installing on. You’ll need to ensure the beam is structurally sound and is not damaged in any way. Installation steps are as follows: Locate a structural beam flange capable of withstanding a 5,000 lb. static load. Push up on the toggle plate to allow the adjustment rollers to move. Keeping the unit perpendicular to the beam, fit the rollers over the edge of the beam flange. Slide the rollers so that both sets are fully resting on the beam flange. Release the toggle plate and pull back on the rollers to ensure the ratchet teeth are fully seated in the nearest notches. Tog, rock, and twist the trolley in all directions to make sure it can’t come off the flange. Screw tight the secondary safety locking screws on the bottom of the toggle plate Rollers must glide on a clear surface, and remove any potential obstacles. Ensure that the beam trolley can’t slide off the end of the beam it is attached to. These steps are a brief overview of the installation procedures required for this fall protection beam trolley — see the manual for more comprehensive instructions and use guidelines. Key Features and Benefits: Innovative Mobility and Safety The Malta Dynamics Beam Trolley is specifically designed to enhance worker mobility and productivity. Its free-moving aluminum rollers ensure smooth and effortless movement along the I-Beam, perfectly trailing the user's movements without compromising safety. This dynamic system significantly reduces the time and effort required to re-anchor, allowing workers to focus on the task at hand with increased efficiency. Durable Construction and Easy Installation Built with high-quality materials, including aluminum, polyester, and stainless steel, this beam trolley is not only lightweight but also incredibly durable. It is designed for quick and straightforward installation, featuring easily adjustable pins and locking toggles that secure the clamp in place, preventing any slippage. This ensures that the device remains firmly anchored, providing a stable and reliable point of attachment for fall arrest or restraint applications. Versatile and Adjustable The beam trolley is versatile, accommodating a wide range of I-Beam sizes from 3" to 10" in width and 1/4” to 7/8” in thickness. This adjustability makes it a perfect solution for various work environments and applications, supporting one user with a weight range of 130-310 lbs. Whether used overhead or at foot level, its design ensures maximum safety and compliance with stringent ANSI and OSHA standards. Comprehensive Compliance Meeting the latest safety standards, including ANSI Z359.18-2017, ANSI A10.32-12, and CE-EN 795, the Malta Dynamics Beam Trolley is a testament to the brand's commitment to safety and quality. It is also compliant with OSHA 1926.502 and OSHA 1910.66, ensuring it meets the rigorous requirements for fall protection devices. Engineered for Optimal Load Support The Malta Dynamics Beam Trolley 3" - 10" 5K is equipment meticulously designed to support a significant load limit, with a static tensile strength of 5,000 lbf (22 kN). This impressive capacity ensures that it can safely accommodate a user load capacity of 130 to 310 lbs., making it suitable for a wide range of fall arrest or fall restraint applications. The device's load-bearing capacity is a critical feature, providing peace of mind for users and safety managers alike, knowing that it adheres to the highest standards of safety and reliability. Why Choose Malta Dynamics Beam Trolley? Enhanced Worker Safety and Productivity The beam trolley's design focuses on enhancing worker safety without sacrificing productivity. By allowing for a full range of accessibility and movement, it ensures workers remain safely tied off, reducing the risk of falls and injuries. This not only protects the individual but also contributes to a more efficient and productive work environment. Robust and Reliable Design Crafted for heavy-duty use, the beam trolley's robust construction ensures it can withstand the rigors of various industrial and construction settings. Its precision ball-bearing wheels and anti-drop plates offer added security and durability, making it an essential tool for material handling and load-bearing tasks. Easy Installation and Versatility With its adjustable width and straightforward installation process, the Malta Dynamics Beam Trolley is designed for versatility and ease of use. It can be quickly set up on different beam sizes, making it suitable for a wide range of applications and environments. Regular inspection and maintenance are simplified, ensuring the device remains in optimal condition for safe use. Guaranteed Satisfaction and Support Malta Dynamics stands behind its products with a manufacturer's warranty and dedicated customer support. Purchasing this beam trolley not only ensures you receive a high-quality safety device but also the peace of mind that comes with excellent customer service and support. Whether you need assistance with installation, or application, or have general inquiries, the team is ready to help. If you have any questions about the Malta Dynamics Beam Trolley, please reach out to us online or at (855) 781-7707! [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
BEAM WALKER SUPER SLIDER 3.5″ – 14″
SKU: A6103. The Beam Walker Super Slider 3.5″ – 14″ (Part #A6103) is a large version (14” capacity) fall arrest anchor designed for use on the top flange of a steel I or H beam. Light, smooth, and easy to use, the Beam Walker Super Slider 3.5″ – 14″ is designed for fall protection, rope access, and work positioning. This I-Beam trolley is the best on the market for worker safety! How to Install the Beam Walker Anchor Installation is straightforward with this Malta Dynamics Beam Walker anchor. You can spend less time installing and more time getting to work. Before installing the safety anchor, carefully inspect it, along with the beam you will be installing on. You’ll need to ensure the beam is structurally sound and is not damaged in any way. Installation: Locate a structural steel beam flange capable of withstanding a 5,000-lbf. static load or meeting OSHA 1926.502 requirements for a safety factor of two. Push in on the latch handle to allow the adjustable hook to move. Keeping the unit perpendicular to the beam, fi t the hooks over the edges of the beam flange. Slide the adjustable hook so that both hooks are snug against the beam flange. Pull back the adjustable hook to ensure the ratchet teeth are fully seated in the nearest ratchet notches. *Always re-adjust according to installation steps 1-6 when moving to a new or different sized beam. These steps are a brief overview of the installation procedures required for this beam walker anchor — see the manual for more comprehensive instructions and use guidelines. If you have any questions about the Malta Dynamics Beam Walker Anchor, please reach out to us online or at (800) 494-1840! Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
BEAM WALKER SUPER SLIDER 3.5″ – 24″
SKU: A6104. The Beam Walker Super Slider 3.5" - 24" (Part #A6104) is a large version (24” capacity) fall arrest anchor designed for use on the top flange of a steel I or H beam. Light, smooth, and easy to use, the Beam Walker Super Slider 3.5" - 24" is designed for fall protection, rope access and work positioning. This I-Beam trolley is the best on the market for worker safety! Product Downloads: Anchor Spec Sheet Declaration of Conformity Manual [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
VERTICAL/FIXED BEAM ANCHOR
SKU: A6105. The Malta Dynamics Vertical/Fixed Beam Anchors are designed for fall protection, rope access, and work positioning. This structural steel beam anchor is constructed with lightweight aircraft aluminum bars and features a 360° swivel D-Ring connection point. The compact and durable design of this fall protection anchor clamp makes it ideal for use in industries like construction, oil & gas, transportation, utilities, and more! When choosing a fall protection anchor, it’s important to know what you’ll be connecting to and that the structure can support a load of at least 5,000 lbs. All Malta Dynamics anchors have. Been tested to meet or exceed the strict standards of OSHA and ANSI. These fall protection clamps provide a fixed beam clamp tie-off point for H-Beams or I-Beams, and can be installed overhead or at foot-level (with the approval of a Competent Person). This fixed beam clamp tie-off point features two paws, one that is stationary and one that can be adjusted to fit a range of beam sizes from 4.5”-12”. Once the paws are positioned around the beam, you tighten down the locking nuts to create a secure anchor point that can safely be used as part of the personal fall arrest system. These vertical beam clamps attach without tools and, because of their removable and reusable innovative design, can be used again time after time. It is important to note, anchors should be inspected before each use and immediately removed from service after exposure to a fall arrest situation. How to Install the Vertical/Fixed Beam Anchor Installation is straightforward with this Malta Dynamics safety Vertical/Fixed Beam Anchor. You can spend less time installing and more time getting to work. Before installing the safety anchor, carefully inspect it, along with the beam you will be installing on. You’ll need to ensure the beam is structurally sound and is not damaged in any way. Installation steps are as follows: Locate a structural steel beam flange capable of withstanding a 5,000-lbf. static load or meeting OSHA 1926.502 requirements for a safety factor of two. Twist lock nut and adjustable nut in a direction to allow the adjustable paw to move. Keeping the unit perpendicular to the beam, fit the hooks over the edges of the beam flange. Slide the adjustable hook so that both hooks are snug against the beam flange. Twist both the lock nut and adjustable nut in a direction that it tightens the paws against the beam to ensure the anchor has little to no play. Tug, rock, and twist the anchor in all directions to ensure that it cannot come detached from the flange. *Always re-adjust according to installation steps 1-6 when moving to a new or different sized beam. **D-ring is centered on the anchorage connector for ease of sliding on beam flanges. Particularly in rope access applications, bodyweight may disengage the centering feature in some loading conditions. This is not a safety concern, but it may affect usability. These steps are a brief overview of the installation procedures required for this vertical/fixed beam anchor — see the manual for more comprehensive instructions and use guidelines. If you have any questions about the Malta Dynamics Vertical/Fixed Beam Anchor, please reach out to us online or at (800) 494-1840! Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
Roof Anchor Standard 12″ or 18″
SKU: A6320/21 Family. The Malta Dynamics Roof Anchor is a fixed-post anchorage solution designed for permanent installation on steel, wood, or concrete rooftops. Available in both 12” and 18” heights, this anchor extends above the finished roof surface to provide a visible, accessible tie-off point—ideal for both new construction and ongoing maintenance work. Choose the 12” model for standard roof setups, or select the 18” option when working with deeper roof substrates that require additional clearance above flashing, insulation, or decking layers. Both versions are constructed from heavy-duty galvanized steel for long-lasting performance and corrosion resistance in tough weather conditions. The round post design fits most standard flashing kits, ensuring a clean, secure install. Each anchor is rated to a 5,000 lb. minimum breaking strength and is fully compliant with ANSI Z359.18-2017, OSHA 1926 Subpart M, and OSHA 1910 standards. Backed by industry-leading prices and proven performance, the Malta Dynamics Roof Anchor is compatible with self-retracting lifelines (SRLs), vertical lifelines, and shock-absorbing lanyards. It also meets window cleaning system requirements—making it a dependable solution for a wide range of elevated work applications. Manual Spec Sheet DoC 12" DoC 18"Price range: $199.99 through $219.99 Select options This product has multiple variants. The options may be chosen on the product page -
Roof Anchor 18″ Threaded Top with Swivel Anchor
SKU: A7320-A6306. The Malta Dynamics Threaded Top 18" Roof Anchor is a fixed post rooftop anchor, intended for permanent applications only. The A6306 has been thoroughly tested (see testing and compliance page on this product) and is compatible for installation on steel and concrete substrates (fasteners sold separately). The 18-inch anchor post functions to extend through roofing materials so that it is accessible both during and after roof construction. The A6306 roof safety anchor is composed of durable galvanized steel, and is compatible for use with SRLs, vertical lifelines, and shock absorbing lanyards. The Malta Dynamics 5K Swivel Anchor rotates 360 degrees, flips 180 degrees, and is zinc coated steel. Mounting hardware included. Meets ANSI Z359.18-2017 and ANSI A10.32-12 Compliant with OSHA 1910 and OSHA 1926 Subpart M Product Weight: 1.5 lbs. Simple mount and bolt on system Easy installation and removal Swivels full 360° Great for first-man-up system Worker Capacity Range: 130-310 lbs. Material: Zinc plated steel Min. Breaking Strength: 5,000 lbs. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
ROOF ANCHOR 18″ THREADED TOP Super Sale! $99.99 (while supplies last)
SKU: A6306. The Malta Dynamics Threaded Top 18" Roof Anchor is a fixed post rooftop anchor, intended for permanent applications only. The A6306 has been thoroughly tested (see testing and compliance page on this product) and is compatible for installation on steel and concrete substrates (fasteners sold separately). The 18-inch anchor post functions to extend through roofing materials so that it is accessible both during and after roof construction. The A6306 roof safety anchor is composed of durable galvanized steel, and is compatible for use with SRLs, vertical lifelines, and shock absorbing lanyards. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
ROOF ANCHOR USA EDITION 12″ or 18″
SKU: A6300/01 Family. The Malta Dynamics Roof Anchor is a fixed-post anchorage solution designed for permanent installation on steel, wood, or concrete rooftops. Available in both 12” and 18” heights, this anchor extends above the finished roof surface to provide a visible, accessible tie-off point-ideal for both new construction and ongoing maintenance work. Choose the 12” model for standard roof setups, or select the 18” option when working with deeper roof substrates that require additional clearance above flashing, insulation, or decking layers. Both versions are constructed from heavy-duty galvanized steel for long-lasting performance and corrosion resistance in tough weather conditions. The round post design fits most standard flashing kits, ensuring a clean, secure install. Each anchor is rated to a 5,000 lb. minimum breaking strength and is fully compliant with ANSI Z359.18-2017, OSHA 1926 Subpart M, and OSHA 1910 standards. Compatible with self-retracting lifelines (SRLs), vertical lifelines, and shock-absorbing lanyards, the Malta Dynamics Roof Anchor also meets window cleaning system requirements—making it a dependable solution for a wide range of elevated work applications. Proud to buy American? Prefer the quality? Maybe you're encouraged to source locally? Either way, this Malta Dynamics Roof Anchor's got your back! Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity 12" Declaration of Conformity 18" [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget]Price range: $277.99 through $317.99 Select options This product has multiple variants. The options may be chosen on the product page -
Roof Anchor 12″ Threaded Top with Swivel Anchor
SKU: A7320-A6305. The Malta Dynamics Threaded Top 12" Roof Anchor is a fixed post roof top safety anchor, intended for permanent applications only. The A6305 has been thoroughly tested (see testing and compliance page on this product) and is compatible for installation on steel and concrete substrates (fasteners sold separately). The 12-inch anchor post functions to extend through roofing materials so that it is accessible both during and after roof construction. The A6305 permanent roof anchor is composed of durable galvanized steel, and is compatible for use with SRLs, vertical lifelines, and shock absorbing lanyards. The Malta Dynamics 5K Swivel Anchor rotates 360 degrees, flips 180 degrees, and is zinc coated steel. Mounting hardware included. Meets ANSI Z359.18-2017 and ANSI A10.32-12 Compliant with OSHA 1910 and OSHA 1926 Subpart M Product Weight: 1.5 lbs. Simple mount and bolt on system Easy installation and removal Swivels full 360° Great for first-man-up system Worker Capacity Range: 130-310 lbs. Material: Zinc plated steel Min. Breaking Strength: 5,000 lbs. Anchor Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity Swivel Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
ROOF ANCHOR 12″ THREADED TOP
SKU: A6305. The Malta Dynamics Threaded Top 12" Roof Anchor is a fixed post roof top safety anchor, intended for permanent applications only. The A6305 has been thoroughly tested (see testing and compliance page on this product) and is compatible for installation on steel and concrete substrates (fasteners sold separately). The 12-inch anchor post functions to extend through roofing materials so that it is accessible both during and after roof construction. The A6305 permanent roof anchor is composed of durable galvanized steel, and is compatible for use with SRLs, vertical lifelines, and shock absorbing lanyards. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
STANDING SEAM ROOF ANCHOR
SKU: A6317. Why Standing Seam Roofs Are Different All types of structures use standing seam roofs, from commercial and residential buildings to industrial complexes. When you work on a standing seam roof, it's not the same as working on other types of roofs. You'll need to approach anchorage differently than other types of roofing. Working on a slanted roof requires careful concentration because it may be easier to fall. You also need to use a different type of anchor than for wood and concrete. The anchor point must demonstrate extreme durability while also being strong enough to offer the best fall protection. The anchor should secure to the roof without causing damage. Standing seam roofs have either symmetrical or asymmetrical panels. The legs are different lengths on the latter and the variances will determine where you stick the anchor point for optimal fall protection. You don’t want the anchor to penetrate the panels, and you must be careful when placing them on the raised interlocking seams that pull each panel together. Working on a pitched metal roof requires the utmost care. Taking preventative measures for this job area can keep your workers safe and protect them from injury in the event of a fall. At Malta Dynamics, we offer a standing seam anchor to keep your workers safe on standing seam metal roofs. With our metal roof anchors, your employees can work freely knowing they'll be protected in the event of an accident. Our standing seam metal roof anchor has a swivel anchor point, allowing workers 360 degrees of motion while they work. We manufacture this product from sturdy aluminum and stainless steel, and our design makes it easy to install with no damage to the roof. In just a few minutes, you can fasten the standing seam safety anchor securely. Once you install this equipment, your workers can attach their self-retracting lifelines (SRLs) and focus on their jobs. How to Ensure the Standing Seam Anchor Points Are in Place Be careful not to over-tighten the anchor points on the standing seam. This could dent the roof. Instead, tighten to the point where you can't move it anymore, but not so much that you need to tug the wrench. Test the standing seam safety anchor before you put your total weight on it. Our customers often say they're impressed by how well it holds. Stay in Compliance With Standing Seam Fall Protection From Malta Dynamics You can protect your workers and your business with the best safety equipment from Malta Dynamics. We have been assisting companies in construction, masonry, manufacturing and many other sectors. We understand what you need, like products that meet OSHA guidelines and fall within strict ANSI requirements. Order our standing seam metal roof anchor today to give your workers a better way to secure their SRLs. For more information, feel free to call 800-494-1840 or reach out online. Buy a Metal Roof Anchor Point Today Show your workers that you value their safety when you use the best products available on the market. Our anchor points provide unmatched durability and flexibility you'll appreciate. Place your order online or call us at (800) 494-1840 to ask any questions about our products. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
PERMANENT ROOF ANCHOR
SKU: VARIOUS. A permanent roof anchor is a significant part of Personal Fall Arrest Systems (PFAS) and Fall Restraint Systems used while working on roofs. When attached to the ridge of a wooden roof and used with compatible safety systems, this safety anchor helps limit the forces associated with fall arrest. It was built to be used with other components of a PFAS that limit maximum arrest forces to 900 lbs. or less. Designed for wood rooftops and permanent applications, the Malta Dynamics roof safety anchors have two D-Ring ends made from top-quality metal (alloy steel) and an 18″ stainless steel body for an exceptionally long life. Like all products at Malta Dynamics, the Permanent Roof Anchor is entirely compliant with all applicable ANSI and OSHA regulations. The Permanent Anchor is designed for ease of installation and built to withstand the toughest environments, ideal for both residential maintenance and construction work. The tensile breaking strength of this rugged stainless steel roof anchor is a minimum of 5,000 lbs. (22.2 kN) in ANSI testing. Even with such powerful capabilities, it weighs just under 1 lb. and features a sleek, discreet appearance. Its unique pre-drilled hole layout also helps minimize truss damage that could occur during installation. Fasteners (nails) are included, too, so you can be confident in the installation. Using these permanent roof anchors alongside the right safety harness can help you create safer, easier fall protection for your team. Browse our selection of harnesses and harness accessories for high-quality equipment from the industry leaders at Malta Dynamics. How to Install a Permanent Roof Anchor Permanent roof anchor installation is straightforward with this Malta Dynamics fall protection anchor. You can spend less time installing and more time getting to work. Before installing the safety anchor, carefully inspect it, along with the roof’s trusses, rafters, and structural members. You’ll need to ensure the roof is structurally sound and that the permanent roof anchor is not damaged in any way. You will also need to select a site that meets OSHA requirements, including minimized swing fall hazards and a limited free-fall distance of less than 6 feet. All employees must be trained by a Competent Person, as defined by OSHA. Explore our training options if your team needs a refresher on fall protection awareness. Permanent roof anchor installation instructions are as follows: Ensure you are working on a roof constructed of wood, the permanent roof anchor is not designed for metal roof materials. Remove 1-2 pieces of the ridge cap if installing on residential roofing with asphalt shingles, shakes, or tile. Center the anchorage device on the ridge of the framing assembly and position it so the nail holes on the center of the legs are directly centered with the middle of the roof framing member. Use 16d common nails to secure the bracket with all provided nail holes. No nails should split the timber or protrude through the side of the members These steps are a brief overview of the installation procedures required for this permanent roof anchor for fall protection — see the manual for more comprehensive instructions and use guidelines. The Malta Dynamics Difference Malta Dynamics specializes in quality fall protection systems and is a trusted industry leader providing safety equipment throughout the nation. We are a full-service manufacturer that takes care of design, engineering, and manufacturing for fall protection products across many different industries. Our equipment exceeds OSHA requirements and is built in an ISO-17025 laboratory that uses ANSI testing procedures for reliable manufacturing practices. We emphasize the use of high-strength materials engineered for durability and long-term performance. Put safety first with a permanent roof anchor that’s designed for the task and meets OSHA standards. If you have any questions about the Malta Dynamics Permanent Roof Anchor, please reach out to us online or at (800) 494-1840! Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget]$25.99 Select options This product has multiple variants. The options may be chosen on the product page -
REUSABLE ROOF ANCHOR
SKU: A6303. The Personal Fall Arrest Systems (PFAS) and Fall Restraint Systems used while working at heights usually include fall arrest roof anchors. The Malta Dynamics Reusable Roof Anchor is a 21” reusable heavy-duty roof anchor with two moveable legs and a steel D-Ring. These fall arrest roof anchors weigh only 2.4 lbs. and are designed with a discreet profile that’s easy to transport. This reusable roof fall protection anchor is designed for temporary use on wood rooftops and fits a range of roof pitches from flat to 12/12. The thick zinc plated steel construction gives this reusable roof anchor system a long life and is ideal for supporting workers ranging from 130-310 lbs. Instructions on how to install a reusable roof anchor are easy to follow. Simply use the pre-drilled holes in the legs as a guide for installation and secure the anchor to the rooftop using screws or the included nail fasteners. This roof fall protection anchor meets or exceeds the safety-oriented requirements of OSHA and ANSI. It meets OSHA 1910, OSHA 1926 Subpart M, ANSI Z359.18-2017 Type A, and ANSI A10.32-12. Using these permanent roof anchors alongside the right safety harness can help you create safer, easier fall protection for your team. Browse our selection of harnesses and harness accessories for high-quality equipment from the industry leaders at Malta Dynamics. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
SINGLE USE ROOF ANCHOR
SKU: A6318. Malta Dynamics Single Use Roof Anchor The Malta Dynamics Single Use Roof Anchor is a must-have for any roofer’s safety kit. Designed to bend easily over the roof peak or adjust to match varying roof pitches, this disposable anchor provides a secure tie-off point without causing permanent damage to the structure. Its versatile shape and reliable performance make it ideal for new construction, remodeling, or reroofing projects. Built from durable zinc-plated alloy steel, this anchor is both lightweight and strong. It installs quickly using the included (8) 16d common nails, making setup fast and hassle-free. With a user weight capacity of 130–310 lbs., this anchor has a minimum breaking strength of 5,000 lbs. and is tested to meet OSHA 1926.502, OSHA 1910.66, and ANSI Z359.18-2017 standards. To ensure maximum safety, always mount the anchor into a solid structural member such as a roof truss or rafter. A fall protection system is only as strong as its anchorage point. Whether you're tackling a residential remodel, or a commercial reroof, this single-use roof anchor helps you get the job done efficiently and safely. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget] -
4-WAY ANCHOR PLATE
SKU: A6304. The Malta Dynamics Multi-Directional Roof Anchor supports one worker in fall arrest or two workers in fall restraint. The four directional connection points increase the working range (when detaching and reattaching to connection points). Workers can maintain both fall arrest or fall restraint. It is designed and tested to meet the latest ANSI Z359.18-2017 standard, ensuring optimal safety and performance for workers. This anchor supports one worker in fall arrest and two workers in fall restraint, featuring four directional connection points that enhance mobility and ease of use. Its versatile design allows workers to safely detach and reattach to connection points while maintaining fall protection, making it an ideal solution for various roofing applications. Product Downloads: Anchor Manual Anchor Spec Sheet Declaration of Conformity [ryviu_question_and_answer] [ryviu_widget_total] [ryviu_widget]
